microphone RJ45

[jamesshao8]

Hello there,

I made one of this 16SoundsUSB according to your design files. I found there is actually no microphone on board, instead there are 16 RJ45 sockets.

According to the schematics, there are already on board input amplifiers, so what I need is some analog microphone units, and connect their outputs to each RJ45 port 2 and 4, right?

Do you have some suggestion about the microphone model/brand?

Thank you!

Regards,
Shao

[jamesshao8]

I just found some design file of microphone for 8SoundsUSB from sourceforge. I will see if I can make them here.

Do you recommend the xtag2 programmer or xtag3?

Thanks.

[qinyunchuan]

I think you should attach a ECM to the RJ45 connector.

[jamesshao8]

It's actually RJ11, I found the design file of MIC-RJ11 board from 8SoundsUSB project. I think they can be used in this 16SoundsUSB project as well. So I am trying to make 16 of them locally. Right now I am working on how to download the firmware to this board. I just found the pre-build *.xe file, thanks to the creator by the way. So I will try again with my XTAG3 debugger.

What is ECM anyway? A type of microphone? I do have plan to customize the MIC board with better microphone for higher sensitivity.

[doumdi]

Please have a look at the microphone designs here : https://github.com/introlab/xSoundsMicrophones. We have electret design and MEMS design available. Also, yes, the microphones are compatible with 8SoundsUSB. We use the same pinout and RJ11 connector.

[doumdi]

Please note : We use RJ11 connectors and cables in a custom configuration, allowing differential signals and power supply to our own microphone design. It is not compatible with any external 3.5mm adapter and microphone. We made this choice to make the system robust to noise, compact and easy to install. Everything is powered by the sound card, using USB 2.0.

[jamesshao8]

Nice! Will take a look at these microphone designs.

[jamesshao8]

Hello @doumdi,
I have read the different microphone design files and related datasheets. I found that the sensitivity of electret microphone is -44dB which is better than the mems one with -38dB sensitivity. And also the pre-amplification in the electret design is 20dB~40dB, so the maximum is 40dB or 100 times, while in mems design the amplification is only 10 times.

So I am assuming the electret design can hear the same voice strength in longer distance than mems design? What is the pros and cons of these two design?

Thanks.

[jamesshao8]

Sorry, I was wrong about the sensitivity, mems with -38dB sensitivity should be better than the electret one with -44dB sensitivity. But which pre-amplification is better is still unknown to me. On electret design I have measured the real max gain is 20 times. Will try the mems one. I might also put those amplifiers in series and see how they work together.

[vrheaume]

Hello James,

Our MEMS microphone board design is more recent and was designed to go along with our 16SoundsUSB. The electret microphone board design dates a few years back (time flies) to when the 8SoundsUSB was designed.

The gain values for both microphones were set in a very subjective / arbitrary manner. We had 2 concerns: we don't want too much gain to saturate the signal chain, yet we want enough gain to be able to hear properly when speaking from a few meters away.

Overall, we like the new microphones better with the 16SoundsUSB than we liked the older microphones with the 8SoundsUSB. However, we haven't done apples-to-apples comparison on the two microphone designs.

The MEMS microphone has better sensitivity (by 6dB) and better SNR (by 2-4dB), according to its specification (but I'm not sure we can really compare the specs since they're from different manufacturers, thus maybe different test conditions). We also experienced much, much less signal degradation coming from electromagnetic interference with the MEMS microphone (which we noticed recently when using the electret microphones a few inches away from a wifi router). The VM1000 MEMS microphone is supposedly waterproof and dustproof, features we haven't explored in-depth yet.

It is possible to change one resistor to adjust the gain on the MEMS microphone board, should you find it desirable. Let me know if you need help with this.

[jamesshao8]

Thank you for your explanation.

I will try to make the mems one locally and compare them with the electret one. I noticed in the mems design R7/R6=10 is the gain, and I replaced R7 to 100k resistor, hoping to get higher gain. I have also bought some mics from knowles. One of them has -18dB sensitivity and 63dB SNR, another one has -40dB sensitivity and 70dB SNR. I am worried about saturating the ADC as well, so I am not sure choosing a mic with higher sensitivity or using higher gain in amplifier would guarantee I can hear sounds for longer distance, but I think higher SNR is always better.

[vrheaume]

In case you haven't noticed, you should be aware that soldering the MEMS microphone is not trivial. The trick I use is to put solder on the PCB pads, then place the microphone with the tweezers, then use the hot air gun to reflow the solder. The MEMS microphone will self-align with the pads as the solder reflows, and then I give it a small push downward with the tweezer to make sure it is flat against the board.

If you go intend to increase the gain, you might want to make sure the opamp's gain-bandwidth specification is respected...

Keep us updated with the results of your experimenting!

[jamesshao8]

We have a partnership with a local PCB/SMT factory. We usually ask them to do small volume prototyping. I think they are able to solder these mems microphones. But for knowles mics, I will have to solder them by myself, connecting them with some wires, so that I can put into my bread board and do the experiments.

We would love to contribute to this interesting project. So sure we will update our result.

[jamesshao8]

Hello @vrheaume,

I have tried the mems mics these days. They are receiving sound in longer distance than electret ones indeed. And my own modification of the resistor increased the distance even further. But the distance is still not enough for me. And in long distance, I can't see obvious beamforming effect as I can in short distance.

Also I am wondering why a basic op-amp is used in the mems design instead of a specialized audio amplification chip in the electret? If I some how connect the mems mic to the amplification chip in electret design, will the distance be even longer? Thanks.